Image titled clean a crystal chandelier step 13
Image titled clean a crystal chandelier step 8
3 Ways To Clean A Crystal Chandelier Wikihow

3 Ways To Clean A Crystal Chandelier Wikihow 3 Ways To Clean A Crystal Chandelier Wikihow

Ensure your crystal is dishwasher safe. Many crystal glasses have a dishwasher safe label. If yours do not, check with the manufacturer or research online to find out if they can be put in the dishwasher.

Crystal manufacturer Riedel notes that their glasses are used in hotels around the world and are thus cleaned in professional dishwashers. If you cannot find any information, err on the side of caution and wash by hand.

[1]

Reassemble the chandelier. Work from your photos or memory to replace all parts, bulbs, and crystals to where they belong in the fixture. While assembling, work from the top down and from inside to out to put all the pieces back together easily.[12]

Clean the frame and other parts. If you need to, clean the frame, bulbs, and any other parts of the chandelier with a soft, dry cloth. Replace bulbs if they are dim, broken, or discolored. You may be able to use the same soapy water or other cleaner on the frame or other parts of the chandelier.

Check first about the variety of metal or other material they’re made out of to find the right cleaner for it. Be sure to thoroughly dry any moisture that has remained in light bulb sockets or other areas of electrical connection.

Dry as best you can with a cloth, then leave parts out to dry further for several hours before assembly if necessary.

Dry your crystal. Gently wipe each item down with a lint-free cloth. This will remove any water spots and give your crystal a beautiful shine. Again, it is a good idea to wear gloves to prevent smudging your clean crystal.[10]

Create a solution of water and vinegar. Fill your sink or a bucket with one part vinegar and three parts lukewarm water. Mix the solution thoroughly. Pad the bottom of your sink or bucket with a soft towel to prevent the crystal from getting damaged.

[11] Vinegar will help remove cloudiness from crystal as well as add a beautiful shine.[12]

Run the dishwasher. Start your dishwasher and allow it to run its normal cycle. Don’t interrupt the cycle or open the door in the middle of cleaning.

No. Car wax often contains a very fine grit for polishing and can actually slightly dull the surface of the glass.

Decide on a deep or shallow clean. If you’ve never cleaned your chandelier, opt for a deep clean by performing the “crystals off” method. Otherwise, the less time-intensive “crystals on” method will typically suffice for regular cleaning.

Choose a deeper clean particularly if there are stubborn spots or a cloudy, milky quality to the crystal that isn’t removed by a simple dusting.

Español: limpiar una araña, Português: Limpar um Lustre de Cristal, Italiano: Pulire un Lampadario di Cristallo, Русский: вымыть хрустальную люстру, Français: nettoyer un lustre en cristal, Deutsch: Einen Kronleuchter aus Kristall reinigen

You can hang an elegant chandelier in your home without breaking your bank simply by making one. There are many ways to make a chandelier, and most take advantage of pre-existing ceiling light fixtures or second-hand chandelier frames. Keep reading for instructions on how to make three simple DIY chandeliers.

Hang the chandelier over an existing ceiling light. For best results, choose a simple light fixture that extends low enough to sit in the top of the planter basket. The light from the existing fixture will appear to “glow” against the paper capiz shells.

Cut and attach ribbon to the planter basket. You will need to cut out anywhere from 90 to 120 strands of ribbon. You can either attach the ribbon in single or double layers. The method you use will determine the needed length of each strand.

Single-layer ribbon should be about 7 in (18 cm) long and double-layer ribbon should be 16 in (41 cm) long. Use a hot glue gun to glue the end of a single-layer strand of ribbon over the horizontal bar of the basket.

Fold a double-layer strand of ribbon in half. Knot the ribbon over the horizontal bar of the basket. Attach your ribbons to each horizontal bar of your basket frame, starting from the bottom and working your way up.

There should be very little excess space in between ribbon strands.

Prepare the area. While you’re waiting for the bulbs to cool, prepare your workspace. Place a tarp or drop cloth over the floor under your chandelier, and set up a stepladder or taller ladder securely under the chandelier.

To prevent any parts dropping and breaking, you can lay down a thick blanket to absorb the fall. Make sure your ladder is at a height that is comfortable to reach all parts of the chandelier.[1]

Cleaning each part of a crystal chandelier can be a tricky, detail-oriented task. However, it’s important to clean your chandelier periodically to maintain the light-reflective quality that makes it so bright. Learn how to properly clean a crystal chandelier to continue enjoying it as a statement piece in your home. These methods will work on chandeliers of authentic crystal as well as ones made with glass or plastic.

I purchased some used platinum rimmed stemware, but the platinum is dark. How can I safely clean it to brighten it?

I cannot get the moisture out of good crystal vases with small openings. What should I do?

Cut out and stack the parchment paper and wax paper. Cut a 36-in (91-cm) piece of parchment paper and three 18-in (46-cm) pieces of wax paper. Lay the parchment paper out on an ironing board and place the three pieces of wax paper inside.

Fold the parchment paper over the wax paper to sandwich the pieces in. The parchment paper helps the wax stick together and stay within the layers of paper. It also creates a smooth, finished surface on the wax paper.

If you do not have an ironing board, you can lay this out on a clean dish towel in the middle of a hard floor or table.

Submerge your crystal in the solution. Allow the crystal to soak for five to ten minutes. If your item is too big to fully submerge, you can fill it with the solution (e.g., a vase or bowl) or dampen a soft cloth or sponge in the solution and use it to wipe down the crystal (e.

g., a lamp or figurine).[13]

Use glass cleaner and clean cotton cloth. Working on your ladder where you can reach the chandelier, spray a glass cleaner or specific chandelier cleaner on a cotton cloth that is clean and soft. Wipe down each crystal with the damp cloth, then immediately dry with a separate dry cloth.

Try wearing an apron with pockets while you work, so that you can keep the cleaner, cloths, and any other supplies easily on hand.[2] Instead of two cloths, you can wear two soft cotton gloves for better control and dexterity.

Spray one glove with the cleaner to wipe crystals down, and keep the other glove clean to dry them. If you have a lot of crystals, you may want several pairs of gloves.[3]

Attach ribbon to the metal frame. Measure a length of ribbon to fit around the wide ring of your metal frame. Cut and sew the ribbon over the ring. You can use any color ribbon you want, but it should be opaque enough to conceal the ends of the tied sequin strands.

Attach the ribbon to the wire using a needle and thread. Place the ribbon over the wire. Pull your threaded needle through the ribbon, around the wire, and back through to the front of the ribbon. Repeat this process until the entire ribbon is attached.

If necessary, you can temporarily hold the ribbon in place with craft glue or hot glue as you sew. You should not rely on the glue permanently, though.

Is there a spray cleaner I can use to clean my chandelier without wiping it?

Can I use a hand held steamer? I have teak crystals and solid brass chandelier.

Dust in between cleanings. To make your clean last longer, use a soft feather or lambswool duster to lightly clear dust from the frame and crystals. You’ll need a stepladder, but you do not need to disassemble the fixture.

[14] A good general rule is to dust every few months, or whenever you notice a visible layer of dust or haziness on the crystals, frame, or bulbs. It’s also a good idea to dust before any wet cleaning, as you can remove larger dust and dirt particles ahead of time.

[15]

Prepare a metal lamp shade frame. Use spray paint to paint the frame white. This is only optional. If you like the current color of the frame, you do not need to paint it. You could also paint the frame black, gold, or silver.

For a brighter, less traditional appearance, you could paint the frame any color that matches the décor of your room. Only use spray paint that is approved for use on metal. Make sure that the wide part of the lamp shade frame is large enough to fit over the existing ceiling light base you plan to attach the chandelier to.

The frame will be turned upside-down when hung.

Clean the crystals carefully. Fill a sink with warm water and a small amount of mild dish soap. Line the sink with a cloth or towel to provide padding. Place crystals into the padded sink and rub each one separately with your fingers in the soapy water before rinsing and placing on a soft, clean towel.

Take care to prevent crystals from hitting against each other or against hard surfaces of the sink to avoid cracking or chipping. There is no need to use a sponge or brush to clean crystals with the soapy water, and in fact this could end up scratching them.

Dry the crystals with a soft, absorbent cloth immediately after rinsing. This is essential to preventing dried water spots from forming.[11]

Use only dry, soft, cotton cloths for cleaning. Avoid paper towels or rough cleaning cloths, as these can easily scratch crystal. If possible, consult a manual or manufacturer’s website for your chandelier to see if it has any tips or warnings about proper cleaning.

If your chandelier is still looking shabby even after cleaning, contact the manufacturer or another source that sells replacement crystals or parts.

Iron the paper together. Use a low setting on your iron. Pass the iron over the paper sandwich several times to melt the layers of wax paper together. Remove the layered wax paper from the parchment. The wax paper should stick together, but it should not stick to the parchment paper.

Turn the light off and let the bulbs cool. Switch off the light switch that controls the power for your chandelier. Wait until the light bulbs on your fixture feel cool to the touch. You can disconnect the electricity as an extra precaution, but only do this if you are confident in operating your home’s circuit breaker or have assistance from a knowledgeable electrician.

You should not need to adjust any electric wiring in this process.

Use a small amount of detergent. Don’t add extra detergent in the hopes of getting your crystal extra clean. Excessive detergent can leave a cloudy film on your crystal. Follow the recommendations for your dishwasher and detergent, taking into account whether you have hard or soft water.

[4]

Paint each disc with nail polish. You will need two colors of nail polish. The light color goes on first, and the darker color goes on second. Pour your first color onto the disc in a spiral swirl. Quickly spread the polish using the nail polish brush so that it coats the entire disc.

Once the polish is spread, smooth it out by brushing it in another spiral from the outside moving in. Only use your wrist as you swirl the polish and make the swirl one continuous line. Pour a small puddle or four to five drops of your second color into the middle of the disc.

Smush it around using the polish brush, working from the inside out. Lightly swirl the nail polish around so that it gradually fades into the first color. The second color should only cover about 1/3 of the surface.

Let dry. If you are unsatisfied with the look of your disc, apply a small amount of nail polish remover to a cotton ball, remove the polish, and try again.

Working with high voltage is dangerous. Consult a qualified electrician if you intend on removing electrical components or adjusting wires in any part of your chandelier.

Carefully wash your crystal with a cloth. Be sure to use a soft cloth or sponge so as not to scratch the crystal items. Gently rub your cloth or sponge on the surface of the crystal using a circular motion.

Cut out circles of wax paper. Use a circle cutter to cut 2.5-in (6.35-cm) circles out of each layered sheet of wax paper. Cut as many circles as possible. If you do not have a circle cutter, you could use a cookie cutter or other circular stencil that measures roughly 2.

5 in (6.35 cm) in diameter. Trace around the stencil using a craft razor or blade. Cut the circles out over a cutting mat. It may help to tape the wax paper to the mat as you work to prevent it from sliding around.

Try to clean every 12 months. Aim to clean your chandelier with either the “crystals on” or “crystals off” method every year for a fixture that remains shining and bright. Observe your chandelier periodically for visible dust, cloudy crystals, or spots.

These are all indications that you should clean your fixture right away. Clean more often if your chandelier is located in a kitchen, as it will build up more grease and grime than in other areas of the house.

Entryways are another area in which a chandelier may need more frequent cleaning.[13]

Make a soft paste with water and baking soda. Gently rub the metal with a soft cloth, rinse and dry.

Yes, you can find sprays that don’t require wiping online. You just need to use a drop cloth to catch any run-off liquid. (I imagine you may need to do a little hand cleaning touch-up though.)

Turn it upside down (so that any water can come out), and when you put it upright, try wrapping a chopstick in a few layers of paper towel (use a rubber band to keep it in place) and wipe away as much as you can.

Using a hairdryer on the cool setting should get rid of any leftover moisture. You can also leave the vase upside down on a drying rack to air dry.

Submerge your crystal in the solution. You’ll want to do one piece at a time to prevent the items from clanking together, which could cause chipping or breakage. If needed, allow your crystal to soak for a few minutes.

[7] If your item is too big to fit in the sink or bucket, or cannot be fully submerged, such as a lamp or chandelier, dampen a soft cloth or sponge in the solution and use it to carefully wipe down the item.

Allow crystal to warm up. Don’t start the dishwasher until your crystal has had time to come to room temperature. Sudden changes in temperature, such as heating a chilled glass, can cause breakage or damage to crystal.[3]

Did you try these steps?Upload a picture for other readers to see.

Vinegar will clean the vessel of debris from mineral buildup, and is safe and gentler than something like window cleaner. Also, water will dilute the vinegar so that the acidity won’t be too strong.

Three Methods:Using the DishwasherWashing Crystal by HandRestoring Shine to Your CrystalCommunity Q&A

Thanks to all authors for creating a page that has been read 122,338 times.

Dry your crystal. Air drying will often leave water spots, so use a lint-free or microfiber cloth. You may want to wear gloves so you don’t get fingerprints on your clean crystal. Carefully pat the crystal dry, rather than rubbing it.[15]

Include your email address to get a message when this question is answered.

Three Methods:Cleaning with Crystals OnCleaning with Crystals OffKnowing When to Clean Your ChandelierCommunity Q&A

Thanks to all authors for creating a page that has been read 34,876 times.

Clean the frame. Wipe the frame and any other parts of your chandelier with just a dry cloth or an appropriate chandelier cleaner or metal cleaner. Ensure that you use a cleaner that is intended for the type of metal or other material that your chandelier frame is made out of, otherwise you run the risk of discoloring or tarnishing it.

Clean any metal hooks or fasteners for the crystals with a dry cloth only, as cleaner can tarnish or strip the finish off of them.[5]

I was advised by the manufacturer to soak a crystal pitcher in a 50/50 solution of water and vinegar before using. Why?

String your ornaments. Create varying strands of clear glass ornaments by tying heavy-duty thread, fishing line, or clear jewelry line to the top wire of each ornament. Attach the thread to the top wire of the ornament, where the hook would usually go.

Knot the thread to hold it in place. The number of ornaments to a strand should vary from about two to six per strand. Create more strands with two to three on them since these will go around the outer edge.

Paint a wire planter basket. Use spray paint to color the basket frame. Make sure to use spray paint that is approved for use with metal. White, black, silver, gold, and bronze paints have the most traditional appeal, but you can use any color that matches with the décor of your room.

Disassemble the chandelier carefully. Carefully remove each crystal from the chandelier and place it on a nearby surface that is stable and covered with a blanket or thick cloth. You may disassemble other larger parts of the chandelier or take down the whole fixture entirely if it is possible to do so safely and without affecting wiring or the fragile parts of the chandelier.

You may need needle-nose pliers or a similar tool to unfasten each crystal piece, depending on your chandelier. You can also use them to reshape the crystal fasteners during reassembly to strengthen them.

[10]

Thanks to all authors for creating a page that has been read 97,280 times.

Gather your materials. You will need a recycled chandelier frame, lucite discs, nail polish, and stainless steel jump rings. The chandelier should have a cylindrical shape and hooks that go around the entire fixture.

Cut costs by buying one at a thrift store or by getting a beat up one by someone who’s ready to throw theirs away. The lucite discs, also known as plexiglass, plastic, or acrylic glass discs, should be 4 in (10 cm) in diameter and about 1/8-in (3 mm) thick.

You need two discs for every hook on your chandelier frame. Use cheap, slightly sparkly nail polish. There’s no need for anything too expensive; cheap nail polish should work fine. Get creative with your color choices.

The stainless steel jump rings should be 20g rings that are about 1/2-in (1.25-cm) in diameter. If you do not want to buy the rings, you can make them yourself by wrapping heavy-duty wire around a 1/2-in (1.

25-cm) tube of lip gloss.

Remove the crystal carefully. You may want to wear gloves or remove the crystal with a lint-free cloth to prevent smudging and fingerprints. You can also use the lint-free cloth to remove any left-over water spots.

To make a chandelier, spray paint a wire hanging basket the color of your choice. Then, flip the basket over and use a glue gun to wrap ribbon around the top cage of the basket with about 0.5 inches (1.3 cm) in between strands. Next, gather large sequins, lucite disks, or long strings of beads to adorn the chandelier. If you’re using sequins or disks, glue them to the ribbon on the chandelier for a reflective surface. If you’re using beads, hang them from string tied or glued to the outer wire of the basket. Hang the chandelier over a light source and enjoy!

Transfer the template marks onto each disc. Place the template beneath each disc and use a marker to mark the template hole dots onto the disc. The dots should be placed in the same position. Even with nail polish painted on each disc, you should be able to see the dots through the lucite.

Rinse your crystal with warm, running water. You can also rinse your crystal in distilled water to help prevent water-spots. Handle the crystal carefully as it can easily slip out of wet hands. You may want to wear gloves to give you a better grip and prevent smudges.

[14] For those larger items, use a clean, wet cloth or sponge to wipe down the item and remove any lingering soap.

Crystal is a beautiful substance and adds an air of elegance to your home when on display. However, it does attract dust, and cleaning crystal glasses, bowls, or vases after a dinner party can seem like a tedious chore. Many crystal items are actually labeled as dishwasher safe, but don’t fret if yours aren’t. Cleaning your crystal with a mild detergent, or soaking it in vinegar to remove cloudiness, is a breeze and your items will be sparkling again in no time.

Create a solution with warm water and mild dish soap. Fill your sink or a bucket with warm water and a small amount of mild dishwashing soap. Too much soap can leave a cloudy film, so only use a little bit.

Swirl or agitate the water to mix the solution thoroughly. Line the bottom of the sink or bucket with a rubber mat, soft cloth, or even paper towels to prevent damage to your crystal.[6]

Hang your discs on the chandelier frame. Attach each double-layer of discs on the chandelier frame by hanging them on the frame’s hooks. Each hook should have a set of discs hanging from it. Hang the discs by their large holes.

It may help to already have the chandelier hanging in place before you attach the discs. This completes the chandelier.

Wash your crystal carefully with a cloth. Use a soft cloth or sponge for washing your crystal to avoid scratches. Gently rub the sponge or cloth on the surface of the crystal in a circular motion, and be sure to clean the entire item, inside and out.

[8] If your item has a narrow opening, try using a baby bottle brush to move a sponge or soft cloth around the inside of the item. Some crystal is etched with language or artistic designs; use a soft-bristled toothbrush dipped in the warm water mixture to brush dust and dirt out of the etchings.

Hang the chandelier. The process may vary depending on how your existing ceiling light base is set up, but these instructions apply to a standard base. Start with a light base that currently has light bulbs in it.

Since there is no light source in this chandelier, you will need to rely on an existing light source. Make sure that the light is currently “off” to prevent yourself from getting shocked. Cut a length of heavy-duty wire that matches the circumference of the light base.

It should be able to fit beneath the light base snugly. Attach four or more strands of heavy-duty fishing line to this wire circle. Attach the other end of each strand to the wide ring of your chandelier beneath the ribbon.

Unscrew your light base slightly. Slide the wire ring you created under the base and screw the plate firmly in place over the wire. Check the light fixture and the chandelier to make sure that both are firmly held in place.

This completes your chandelier.

Drill the holes into each disc. Any standard drill should work. To drill the large hole, first drill into the large marking with a small drill bit. Widen the hole with a medium drill bit, and widen it again with a large drill bit.

Do not drill the hole with a large bit from the start, since doing so will likely crack the lucite. For the smaller hole, drill the hole using a small drill bit. Half the discs should have both holes drill into them while the other half only need the small hole drilled in.

After washing and cleaning my quartz crystals, what chemical should I apply to make the crystals sparkle?

Three Methods:Glass Orb ChandelierPaper Capiz Shell ChandelierLucite Disc ChandelierCommunity Q&A

Clean all crystals carefully. Work your way around the chandelier to clean every crystal with your cleaner and cloth, wiping with the damp cloth or glove and drying with the clean one. When cleaning the crystals, always spray cleaner onto a cloth first, rather than directly onto the fixture.

While cleaning, don’t twist or rotate the chandelier to access each side or part. This could damage or weaken its parts or supports, risking falling and breakage. Instead, carefully descend and move the ladder to position yourself in the right spot to reach and clean each part separately.

[4]

Repeat the paper ironing steps. Continue creating stacks of three-layered wax paper until you use an entire roll of wax paper. For large planter frames, you may want to use half of a second roll, as well.

You do not need to use new parchment paper for each layer. The parchment paper can be reused.

Turn off the light to let the bulbs cool. Turn off the power that controls your chandelier. Wait to do any work until the light bulbs on your fixture feel cool to the touch. You do not need to disconnect the electricity, but you may as an extra precaution since this step involves disassembling the fixture.

Disconnect power from the room only if you are confident in operating your home’s circuit breaker or have assistance from a knowledgeable electrician. You should not need to adjust any electric wiring in this process.

Awesome picture! Tell us more about it? Click here to share your story.

Make a paper template for your discs. Trace the outline of one disc onto thick paper. Cut it out and mark where the holes should be. This template allows you to determine where you need to drill each hole in your lucite disc.

Fold the paper template in half so that you can locate the exact middle. Use a marker to draw a big hole roughly 1 in (2.5 cm) away from the edge and along the center line. Draw a smaller hole about 1/4 in (0.

635 cm) away from the opposite end along the center line.

Prepare the area. While you’re waiting for the bulbs to cool, prepare your workspace. Place a thick blanket on the floor under your chandelier, as well as across a nearby table or whatever surface you plan to place chandelier parts on.

Set up a stepladder or taller ladder securely under the chandelier. A heavy, thick blanket or cloth is essential for underneath your workspace, as it will soften the landing and prevent breakage in the case of pieces falling during disassembly.

If you don’t have one, fold over another cloth several times to make it thicker.[7] Make sure your ladder is at a height that is comfortable to reach all parts of the chandelier.[8] Inspect your chandelier and take photos from several different angles and distances so you will remember how to reassemble it later.

[9]

Let the crystal cool. Allow the dishes to cool before opening the door to the dishwasher. This will also let your crystal dry in case the dish-washing cycle didn’t fully dry the crystal. Depending on your dishwasher and water temperature, this could take several hours.

[5]

Load the dishwasher carefully. Ensure your glasses, bowls, or other crystal items have enough space. You don’t want them touching, as they could jostle and bump into each other causing damage during the dishwashing cycle.

Don’t overcrowd or overload the dishwasher, and be sure any long-stemmed glasses fit securely in the rack.[2]

Glue the paper capiz shells onto the ribbons. Use a small dot of hot glue to attach the top of each shell to the ribbon. Only attach the shells to every other ribbon and alternate between two and three shells per ribbon.

The shells on each strand should overlap by about 1/4-in (0.635-cm). Start with the bottom layer and work your way up to the higher layers. Continue until the layers of ribbon on each tier have been decorated with the capiz shells.

Italiano: Realizzare un Lampadario, Español: hacer un candelabro, Русский: сделать люстру, Português: Fazer um Lustre, Français: fabriquer un lustre, Deutsch: Einen Kronleuchter basteln, Bahasa Indonesia: Membuat Lampu Gantung

Create strands of sequins. Use a sewing needle to weave heavy-duty thread through a series of eight sequins. Create three to four dozen strands. Push the thread through the same side of each sequin in the strand.

Then, repeat the process by knotting the thread and weaving it through the opposite side of each sequin. The sequins should be flat against the thread when done. Use gold and silver sequins. You can either create solid strands of gold and solid strands of silver, or you can mix the colors on each strand.

Use light or clear thread for the best results. You could also use metallic thread that matches the color of the sequins. If you would prefer an asymmetrical look, you can alternate the number of sequins on each strand, varying the length from 6 to 10 sequins.

The exact number of strands you need will depend on how large your chandelier will be and how full you want it to appear.

Rinse thoroughly. Use warm, running water to rinse away any residue from the crystal. You may want to wear gloves to ensure you aren’t putting fingerprints on your clean crystal. For those larger items, use a clean, wet cloth or sponge to wipe down the item and remove any lingering soap.

You could also rinse your crystal in a bucket or bowl of distilled water, as this will reduce the amount of water-spots left behind.[9]

Español: limpiar cristal, Русский: очистить хрусталь, Português: Limpar Cristais, Italiano: Pulire il Cristallo, Deutsch: Kristall reinigen, Français: nettoyer du cristal

Crystal that is edged with gold, silver, other gilding, or with paint should not be allowed to soak in the warm water mixture. Wash each item with a cloth or sponge dampened with the warm water mixture.

Dust light bulbs gently. Clean off the light bulbs in your fixture with a clean, dry cloth. Make sure that all bulbs are screwed in properly and don’t appear browned or discolored. If any light bulbs are dim, burnt out, broken, or missing, take this opportunity to change them out with new bulbs of proper wattage.

[6] If a bulb appears to have more stubborn stains, you can very gently clean it with a cloth damp with cleaner, or replace the bulb entirely.

Attach your sequins and ornaments to the frame. Turn the frame upside-down. Tie and knot the sequin strands to the wide part of the frame and the ornament strands to the small ring and “Y” wire stretching across the smaller ring.

Arrange your sequin strands in whatever order you would like. For a nice, full look, you should position the strands so that the distance in between each one is slightly smaller than the diameter of each sequin.

Arrange the ornament strands so that the shorter strands are attached to the ring while the longer strands are attached to the “Y” wire.

To clean crystal, soak it in 1 part white vinegar and 3 parts water for 5-10 minutes. If your crystal is too big to fully submerge in the solution, dip a cloth in the diluted vinegar and wipe the crystal down instead. After the crystal has soaked in the solution for 5-10 minutes, wipe it down with a soft cloth and rinse it with warm water. Then, dry your crystal with a clean cloth so water spots don’t form on it.

Link the discs together. Attach two discs together using one of your stainless steel jump rings. Link the discs together by joining them at the small holes. You will likely be able to open and close the rings with your fingers, but if not, use a pair of pliers.

Remove the arms and with a handle sponge wash it up with Fairy Liquid.

Only to remove rust. If there is no rust, you should not use vinegar.

Handle fine drinking crystal by the bowl and not by the stem or foot to avoid breaking the stem. Hold larger pieces in a dry towel in the hand you are not using to clean the item as wet hands may let the crystal slip.

Store crystal in its original packaging or right side up in a cabinet away from everyday use to avoid contact damage.

Related Images of 3 Ways To Clean A Crystal Chandelier Wikihow
Image titled clean crystal step 10
Image titled clean a crystal chandelier step 2
Image titled clean a crystal chandelier step 15
Outstanding 3 ways to clean a crystal chandelier wikihow how to clean a crystal chandelier
Image titled clean crystal step 17
Uploaded 3 years ago
Image titled clean crystal step 1
Image titled clean a crystal chandelier step 3
Image titled clean crystal step 2
Image titled clean a crystal chandelier step 11
Image titled clean a crystal chandelier step 4
Awesome 3 ways to clean a crystal chandelier wikihow how to clean crystal chandeliers
How to clean a crystal chandelier and housekeeping tips home cleaning techniques with hqdefault 480x360px
Image titled clean pewter step 1
Image titled clean a crystal chandelier step 10
Image titled clean a crystal chandelier step 9
Image titled clean a crystal chandelier step 1
Image titled clean crystal step 13
Related Post of 3 Ways To Clean A Crystal Chandelier Wikihow
Iron And Crystal Chandelier Niermann Weeks

Iron And Crystal Chandelier Niermann Weeks

Iron And Crystal Chandelier Niermann WeeksIron And Crystal Chandelier Niermann Weeks Iron And Crystal Chandelier Niermann Weeks . . . […]
Restaurant Valentin Lindau Good Food Fine Wine

Restaurant Valentin Lindau Good Food Fine Wine

Restaurant Valentin Lindau Good Food Fine WineRestaurant Valentin Lindau Good Food Fine Wine Restaurant Valentin Lindau Good Food Fine Wine […]
Kitchen Lighting Ideas Crate And Barrel

Kitchen Lighting Ideas Crate And Barrel

Kitchen Lighting Ideas Crate And BarrelKitchen Lighting Ideas Crate And Barrel Kitchen Lighting Ideas Crate And Barrel . . . […]
Christmas Rope Lights The Range

Christmas Rope Lights The Range

Christmas Rope Lights The RangeChristmas Rope Lights The Range Christmas Rope Lights The Range . . . . . . […]