3 Ways To Paint Glass Lamp Shades Wikihow

August 15, 2018 4:00 am by sandiego
3 ways to measure a lamp shade wikihow how to measure a lamp shade image titled
Image titled paint ceramic step 27
3 Ways To Paint Glass Lamp Shades Wikihow

Take apart the lamp shade. How you do this depends on the type of lamp you have. In most cases, you will have to remove the lamp shade from the fixture first, then pop the glass panels out.

Three Methods:Painting a Lamp Shade a Solid ColorAdding Stenciled DesignsCreating a Faux Stained Glass LampCommunity Q&A

Consider baking to set the paint. Baked paints last longer than unbaked paints. If you don’t want to go through the hassle of baking your painted glass, there are varieties that you can find which don’t require baking.

Resin-based paints are removable until baked. If you mess up using a resin-based paint, it’s perfectly acceptable to start over. The paint won’t become permanent until the glassware is baked.

Cover the inside of your lampshade with glitter. The glitter will reflect the light and make it seem brighter. Coat the inside of your lampshade using a white, liquid glue. Dump some glitter onto the glue and roll the lampshade around to spread the glitter.

Set the lampshade right-side-up and let the glue dry. If you are worried about the glitter shedding, brush on some clear, glossy Mod Podge, or spray it using a clear, glossy, acrylic sealer. You must use a glossy Mod Podge or acrylic sealer.

If you use matte, the glitter won’t sparkle. You can use chunky glitter or fine, scrapbooking glitter. You can find both in an arts and crafts shop.

Touch the designs up using a thin brush, if necessary. Sometimes, the paint does not reach the edges of the design, and you don’t notice this until is it too late. If there are any bare patches in your design, take out a thin paintbrush and some extra paint.

Carefully fill in those patches using the thin paintbrush.

Choose an appropriate fabric. The best type of fabric to use would be something thin and lightweight so that the light can pass through it. If the fabric is too heavy, the light won’t shine through, and will only come out the top and/or bottom of your lampshade.

Lightweight fabrics include cotton and silk. Heavy fabrics include satin, brocade, velvet, and canvas. You can also use paper for this as well.

Let the lampshade dry entirely before you use it. This can take anywhere between a few hours to a whole day. It depends on how much Mod Podge you used, and how dry or humid it is.

Consider priming your lampshade. If your have a dark colored lampshade and want to cover it with a light colored paper of fabric, some of that dark color might show through. This might not give you the result you want.

To get a better finish in the end, paint your entire lampshade with a white primer. You can use spray paint, a foam roller, or a paintbrush. This will help the lighter colors on your paper or fabric show up better.

Trace your panels onto a sheet of paper, then create your design. Place each panel onto a sheet of paper, then trace around it with a pen or pencil. Lift the panels away, then draw your design inside the panel.

Make sure that all of the lines connect, just like in real stained glass.[9] You don’t have to invent the stained glass designs yourself. Try coloring book pages or stained glass templates.

Follow instructions on paint package for baking. Different paints will need to be baked according to different instructions, so check the instructions before putting your glass in the oven. A glass might go into a 300° F (~150° C) oven for 30 minutes before it’s properly baked.

Allow the glass to cool adequately before handling.

Select your paint. When it comes to glass paint, choose from among from among several different options available. For decorative painting purposes, glass paint falls into three basic categories: Acrylic enamel paint or enamel paint that’s usable on glass as well as other shiny or slick surfaces.

Acrylic paints that become paints for use on glass when a glass and tile medium is added. Specialized solvent-based paint. Know that when it comes to paint, you’ll get what you pay for. While cheap paint may be the best to experiment and play with, if you’re thinking about painting a showpiece or something higher-grade, it’s best to opt for nicer paint.

Cheaper paint doesn’t apply as well, look as brilliant, or last as long.

Consider looking online and in catalogs for ideas. Consider basing your lamp off of a theme, such as holiday or nature. If you don’t want the decorations to be permanent, use clear, double-sided sticky tape instead.

Glue and paint will stick better to lamp shades made out of paper or fabric than lampshade made out of glass or plastic. Tube, cube, or tapered lampshades are easier to work with than domed, asymmetrical, or beveled/paneled lampshades.

How do I curve the bottom of a landscape photo to fit the curved bottom of a conical lamp shade?

Position the lampshade onto the fabric. Make sure that one of the cut straight edges is lining up with the seam of the lampshade. There should be ½ inch (1.27 centimeters) of extra fabric above and below the lampshade.

You need this extra fabric because you will be folding it over later on.

Let the lampshade dry completely before using it. Refer to the label on your paint bottle for specific drying times. Some paints are fully dry and cured in as little as 20 minutes, while others require 2 to 4 hours.

Some need more time than that before you can use them without worrying about ruining the finish.

Can I use acrylic paint that I use on canvas to paint a glass vase?

Not all decoupage glue is waterproof. Do not use it on outdoor lamp shades. If you must use it outside, paint just the inside of the lamp shade.

Inspect the glass paint for several different qualities. When it comes to glass paint, you should look at transparency, color range, permanence, and ease of application. Transparency: how transparent is the paint you’re buying? Glass paints come in both transparent and opaque colors.

Acrylic paints are usually used for opaque colors, while resin paints are usually used for transparent colors. Transparent colors come both in glossy and frosted varieties. Color range: look for a true color chart of what the colors will look like on actual glass.

Sometimes, paint will look significantly different on glass than it does on the color chart. Permanence: especially for items, such as wine glasses, that will be used, permanence and durability is very important.

Paints that have been baked are usually more durable than paints that haven’t been.[1] Ease of application: how easy is the color and pattern to transfer? Does the paint come with any stencils or transfers, or must you make your own?

If the paint you use is opaque (not transparent), it will cover other color, but will not let light through. If the paint you use is transparent, you will get a visual color mixing, and your green leaves will more than likely end up looking brown.

Tape off any areas you don’t want painted. Use painters tape or masking tape to do this.[3]

Dab the paint onto the stencil. Use a foam brush or a stencil paintbrush, and dab the paint on using a light, tapping motion. Do not apply too much paint at once, or the paint may drip under the stencil.

Don’t worry if the lampshade’s color shows through the stencil; you can always apply a second layer.

Trace around the template, leaving a ½ inch (1.27 centimeter) seam allowance all around the template. You need this extra space, because you will be folding it over into the lampshade.

Wipe the surface down with rubbing alcohol. This will remove any oils or residue that might prevent the paint from sticking. From now on, only handle the lamp shade from the inside, otherwise you might get those oils on the part you’re painting.

Read and follow all instructions for each glass paint product. Some glass paints require an undercoat before application and an overcoat after applications; painting without following the directions may result in a failed end product.

Thanks to all authors for creating a page that has been read 1,824 times.

Pour your desired glass paint into a disposable container. You can find glass paint in the glass painting section of a craft store. It comes in many different finishes, including translucent, opaque, glossy, and matte.

Some glass paints even have sparkles in them![1] A translucent finish will allow the most light to pass through while opaque will look more like acrylic paint. A matte finish will give you a sea glass effect.

Make sure that you are using glass paint and not stained glass filler. Stained glass filler is too fluid for this.

Cut your material into small squares. Try to keep the squares proportionate to the lampshade itself. For a very small lampshade, try cutting the squares 1 by 1 inch (2.54 by 2.54 centimeters). For a larger lampshade, try 3 by 3 inches (7.

62 by 7.62 centimeters).

Spray paint the frame, if desired. Take the frame outside or into a well-ventilated area. Set it down onto a sheet of newspaper, then give it 1 to 2 coats of black spray paint. Let the paint dry 15 to 20 minutes between coats of paint.

[8] Spray paint formulated for metal will work the best. If you can’t find any, spray the frame with primer first. Let it dry, then apply your desired spray paint.

Know that this method won’t work on beveled lampshade. If your lampshade is beveled, it likely has multiple sides or panels to it. This method will not work on this sort of lampshade. Instead, click here to learn how to cover your beveled lampshade.

Choose an appropriate lampshade. Almost any shape will work for this method. You might want to use a lighter colored lampshade, however, especially if you plan on covering it with tissue paper. Because tissue paper (and certain types of fabric) is so thin, the original color of the lampshade will show through.

A lighter color, such as ivory or white won’t make much of a difference, but a darker color, such as black, burgundy, or navy, will. You might not even see the colors of your tissue paper. If you can’t find a light colored lampshade, you could paint your current lampshade white.

Keep in mind, however, that the light may not pass through the lampshade as well anymore. You’ll end up with a softer glow.

Fill in the design with your glass paint. The lead you have already applied should stop the paint running out of the desired area. Make use of a sticky stencil. Stick stencils, placed on the opposite corner of the glass, adhere well and give you a good visual suggestion to follow.

Allow the paint to dry and clean your supplies. How long the paint takes to dry depends on the type of paint you used. Acrylic paint dries within minutes, but glass paint can take several hours. As the paint is drying, use this time to clean your pouncer and stencil.

Wipe your stencil down with rubbing alcohol. If you have a self-adhesive stencil, be careful not to get anything on the back. Wash pounces using soapy water or brush cleaner. Be aware that it may not be salvageable and you may have to throw it out.

Before you paint glass, apply an undercoat to the surface of the glass if the paint directions require one. Draw your design with lead paint or permanent marker, or lay a sticky stencil onto the glass. Use a pipette to drop paint onto the surface for small designs, then use a paintbrush to spread the paint where you need it. Apply the paint with a sponge if you want to paint the glass all one color. Follow the directions on the paint package to determine whether to bake the glass to dry the paint.

Spray the outside of lampshade and wrong side of the fabric with spray adhesive. Use straight, even strokes. Try to overlap each stroke by a little to prevent any gaps.

Apply glass paint over the stencil with a pouncer. Squirt some glass paint onto a disposable plate or palette. Dip a foam pouncer into the paint, then tap it against the stencil. Work your way from the outside edges of the stencil towards the middle.

You can use glass paint in any finish you want, but be aware that translucent glass paint may not show up well, especially against a previously-painted surface. If you painted your lamp shade with tinted decoupage glue, use acrylic paint.

Tinted decoupage glue will be too fluid for this step.

Consider priming the lampshade. If your lampshade is a very dark color and you are planning on using a lighter color of paper or fabric, you might want to paint the lampshade white first. You can apply white acrylic primmer with a paintbrush or a foam brush.

You can also spray the entire lampshade using a white primer spray paint.[13]

Adhere a stencil over the lamp shade. You can use regular stencils or self-adhesive stencils. If you are using a regular stencil, tape down all 4 edges with painter’s tape. If you are using a self-adhesive stencil, peel it off of the backing first, then press it down onto the lamp.

[5] Choose an ornate stencil with thin lines so that the light can pass through. Flourishes, filigree, and ornate butterflies make great choices.

Glue doilies all over the lampshade. Choose several tatted or crocheted doilies. They can be all the same size and color, or they can be different ones. Spray the back of a doily with spray adhesive, then press it onto the lampshade.

Add as many doilies as you want. Consider overlapping the doilies by a little.

Awesome picture! Tell us more about it? Click here to share your story.

Choose your material. For this project, you will be gluing bits of paper, fabric, or tissue paper to create a patchwork or paper mache effect. Tissue paper will give you a translucent effect, whereas paper will give you the most opaque one.

You can use scrapbooking paper, map pieces, or pages torn from an old book.[7] If you want the text appearance that book pages can give you, but don’t want to tear up any books, then consider using newspaper instead.

Start applying a thin layer of paint and let it dry. Don’t worry if some of the original color of the lamp shows through. You will be painting on another layer or two. It is better to apply paint using many thin layers rather than one thick layer.

This will help prevent brushstrokes in the finished piece.

Follow the instructions on the glass paint exactly. You can bake them, but have to start them out in a cold oven, bake, and then leave them inside until the oven cools down again.

Pin the panel onto the fabric and trace around it. Leave a ½ inch (1.27 centimeter) seam allowance all the way around the template.

Add a trim to the top or bottom of the lampshade. You can use ribbon, rickrack, braided trim, beaded trim, feather boas, bridal lace, or even a sequin trim. Use fabric glue or hot glue to attach the trim to your lampshade, and cut the excess off.

Fabric glue and hot glue set quickly. It might be a good idea to apply the glue only an inch (2.54 centimeters) at a time. If you have a trim with beads dangling from a ribbon, consider gluing the ribbon to the inside of the lampshade.

This way, you won’t see the stitching, and the dangling beads will be sticking out from underneath the lampshade.

I am painting used alcohol bottles different shapes and colors. Is the acrylic paint ok and can I bake these bottles?

Reassemble the lamp once the paint has dried. If the paint still feels tacky, it has not finished curing yet. Let the lamp dry for a few more days before you reassemble it. If you try to put it back together too soon, the sticky paint will pick up dust and dirt.

If you want to add a stenciled design to your lamp shade, read on to the next section before you reassemble it.

Keep the white spirit or corrective wipe handy to quickly clear any mistakes made. Remember most glass painting (picture wise) will be displayed from behind, i.e. the opposite side of the glass, to the one you paint on, in this case you don’t need to worry about paint overlapping a little onto the lead, as it won’t be visible from the front side.

Seven Methods:Getting StartedAdding Trim and BaublesPainting a LampshadeApplying StencilsCreating a Patchwork LampshadeCovering a Drum Lampshade with FabricCovering a Beveled Lampshade with FabricCommunity Q&A

Water may not remove glass paint from paintbrushes. Try rubbing alcohol, paintbrush cleaner, or other solvents. If the lamp shade gets dirty, wipe it down with a damp cloth.

Cut the fabric out and remove the template. You can use regular fabric scissors or pinking shears. Be sure to cut the rest of the panels out of the fabric. For example, if your lamp has six sides to it, then cut six panels.

Fold the excess ribbon into your lampshade. Place a drop of glue on the end of the ribbon and press it down into the lampshade. Repeat this step for the rest of the ribbons.

Add a ribbon to the inside of the lampshade to hide the seams. You can also use hem tape. Try to use a color that matches your fabric color, or the inside of the lampshade. Place a line of glue all the way around inside the lampshade, right on top of the fabric hem.

Press the ribbon or hem tape onto the fabric. If you come across a metal bar, then try to slide the ribbon under the bar, instead of over it.[12]

Allow the paint to dry before applying the second layer, if necessary. Sometimes, one layer of paint will give you enough covered. Other times, however, a single layer is not enough. If you still see some of the original color peaking through, apply a second layer, and if necessary, a third.

Be clear that there are transparent and opaque varieties in all colours of glass paint, so check carefully you do have the correct effect, as well as colour when you buy, its not cheap, if you get it wrong.

When you thin your paint, stir it slowly don’t ever mix, whisk or shake it. Air bubbles are disastrous and near impossible to get rid of when you have done this. Keeping your paint in the right thickness for use is recommended, don’t over-thin, but using paint that is too thick will result in a lumpy disaster.

Thanks to all authors for creating a page that has been read 382,348 times.

Spray the outside of lampshade and the panels with spray adhesive. Use straight, even strokes. Also, try to overlap each stroke by a little. This will prevent any gaps. When spraying the fabric panel, make sure that you are spraying the wrong side of the fabric.

Roll the lampshade across the fabric. Keep rolling until you have 1 inch (2.54 centimeters) of fabric left over.

Cut the fabric out and remove the template. You can use regular fabric scissors or pinking shears.

Find a suitable lampshade to decorate. Some lampshades are easier to work with than others. When choosing a lampshade, consider the following: Glue and paint sticks better to lampshades that are made fabric or paper than lampshades that are made out of plastic or glass.

Cone, box, or tube-shaped lampshades are easier to work with than domed or asymmetric lampshades. Lampshades that have a smooth surface are going to give you more freedom than ones that already have a textured surface (such as being covered in beads, glitter, trim, or sequins).

Cut the template out and pin it to your fabric. It does not matter which side of the fabric you are pinning it to. What you do want to keep in mind, however, is the pattern and grain of the fabric. The fabric must be smooth.

If there are any wrinkles in it, you must iron them out.

Get a brush. Know that a special paint brush is not required. It’s okay to use your regular painting brushes (rounds, liners, or flats) with synthetic hairs or synthetic mix. Some people prefer the softness of all natural hairs.

Use synthetic or natural-hair brushes. Synthetic and natural brushes can both be used to paint glass; they have different advantages. Synthetic brushes leave more visible brush strokes, while natural-hair brushes give the artist a smoother coverage.

If your glass lamp shade is looking lackluster or dull, consider painting it. A quick coat of glass paint can transform any lamp shade from boring to interesting. If you have more time on your hands, you can even add a stencil. If you are feeling more adventurous, you can turn a paneled lamp shade into a faux stained glass lamp shade instead!

Place the lampshade seam-side down onto the paper. If the lamp is wider at one end, place the lamp at a slight angle. If the lampshade is a perfect cylinder, then place it parallel to the edge of the paper.

Decorating lampshades is a great way to update the look of a plain, dull, or mundane lampshade. This article will give you a few decorating tips. It will also show you how to paint a lampshade, add stencils, and even cover it with paper or fabric.

Seal the seam. Fold the edge in by ½ inch (1.27 centimeters). Press it down onto the lampshade. It should overlap the raw edge by a little.

How do I create shades of a color and blend it together; like a color of a leaf with light green, dark green and yellow.

Clean the glass panels with water and rubbing alcohol. Wash the panels with warm, soapy water first. Rinse them with plain water, then dry them off with a towel. Wipe them down with rubbing alcohol when you are done.

This will remove any residue and oils that may keep the paint from sticking. From now on, try to handle the glass by the edges as much as possible, otherwise you might get oil onto it.

Allow the paint to dry before applying the stencil to another area.[6] If you want to apply more designs to your lampshade, then wait until the paint is dry to the touch; this will usually take about 20 minutes for most brand of paint.

Try not to cover up a previously-painted area with your stencil. This might cause the paint to smear if it is not fully dry.

Apply a second coat of paint once the first one has dried. You will notice that the original color is disappearing. If necessary, apply a third layer.

Keep applying the squares until the entire lamp is covered. You can line them up side by side to create a quilt-like effect. You can also apply them at different angles to create a patchwork or paper mache effect.

Whatever design you decide on, try to overlap each square by a little; this will help prevent any gaps from showing up in the finished piece. Be sure to cover both the top and bottom rim of your lampshade.

Do this by folding the excess paper or fabric over the top/bottom of the lampshade, and pressing it against the inside. This will give you a clean, finished-looking edge.

Pull the stencil off while the paint is still wet.[5] Use both hands to pull the stencil off upwards so that you do not smudge the wet paint.

I want to place a sheet of painted glass in my door window. Is there special glass I should purchase that can be baked?

Cut the panel out of the tracing paper. This will be your template.

Fold the top and bottom seams into the lampshade. If your lampshade has a scalloped bottom, then you will need to cut little nicks into the seam allowance to get it to curve right. If there are any metal bars, you will need to cut little nicks into the fabric as well, so that the seam can lay flat against the inside, to either side of the metal bar.

Apply more stencils, if desired. At this point, you can repeat the process to apply more stencils for a layered look. You can also apply stencils to other parts of the lamp shade. Let the paint dry after you peel the stencil away.

For example: If you added 1 big butterfly, you might want to add 1 or 2 smaller butterflies. If you added a filigree heart, a flourish to either side of it might look pretty. If you added a flower in 1 color, consider adding 2 more flowers in other colors.

Swirl 2 colors together if you want a marbled look. Apply your first color to 1 side of the space, and your second color to the other side. Swirl them together towards the middle with a brush.[17]

Remove, clean, and dry the lamp shade. Remove the shade from your lamp. Wash the shade with warm, soapy water, then rinse it off. Dry the shade off with a paper towel.

You can, but it cannot go in a dishwasher afterwards or be cleaned with a harsh cloth. Make sure to wash it gently with warm soapy water and then rinse, and your glass should last a long time.

Glue fake flowers all over the lamp for a puffy, tufted look. Put a drop of hot glue on the back of the flower, and press it against the top of the lamp shade. Glue the second flower right next to the first one, so that the petals are touching.

Keep gluing flowers until the entire lampshade is covered and no fabric is showing.[1] If you are using flowers that come on a stem, pull them off the stem first. They should just pop off. If they don’t, snip the flowers off as close to the base as you can using wire cutters.

[2]

We have a storm door on the house that has red tulips stained onto the glass. Can I paint on top of these to try to make them look like green leaves instead?

Mix detergent in water, and put the piece of glass in that detergent water. Leave overnight, and then scrape it off with your fingernail.

Spray paint the inside of your lampshade gold to give it a warm glow. Shake the can until you can’t hear it rattle anymore. Then, spray the inside of the lamp using light, even strokes. Be sure to overlap each stroke by a little bit to prevent any gaps.

If you need to apply a second layer, wait for the first one to dry first.

Peel the stencil off before the paint dries. Do not let the paint dry in the stencil, or you risk peeling it off. As soon as you finish applying your last stroke of paint, peel the stencil off. Avoid dragging the stencil across the lamp shape; otherwise, the paint may smear.

Instead, pick the stencil up by 2 corners and lift it straight up.[6] If you notice any chips or gaps in the paint after you remove the stencil, fill them in using spare paint and a thin, pointed brush.

Start with primary. When you get the shade you want, use black to dull it, white to make it paler, or the opposite colors on the color wheel to brighten it.

Combine different methods for a fancier lamp. For example, you can paint or cover your entire lamp with fabric first. Then, you can add a trim to it to give it a final touch.

Use parchment paper to make a template of the lamp shade. It is semi-transparent and you will have enough length to wrap around the shade. Depending on the angle and size of the shade, you may need to do it in 2 pieces.

Lay the template over the photo to find the best position for the image.

Fill the spaces in your design with glass paint. Purchase bottles of glass paint from the craft store; choose the type that comes with a nozzle. Squeeze the paint into each space of your design. Make sure that the paint fills the spaces between the leading completely.

You may have to spread it with the nozzle.[15] Mix your own glass paint by mixing clear school glue with acrylic paint. Use 1 to 2 drops of acrylic paint to 1 tablespoon of glue.[16] You can use stained glass filler for this step.

It is thinner and more fluid than other types of glass paint. It tends to be translucent. Glass paint comes in different finishes. Translucent will look the most realistic, but you can try matte, opaque, or sparkly.

Press the first square down onto the Mod Podge and smooth it out. You can smooth it out using your fingers. If you don’t like getting messy, you can also use the paintbrush or foam brush you were using earlier.

Clean the glass. Make sure that the glass you’re going to paint is adequately cleaned before continuing.

Use a sponge (optional). A sponge will provide uniform, even coverage, and is the best implement to use if you’re painting an entire piece of glass one color.

Remove any tape and allow the paint to dry before using it. Most paints will dry to touch within 20 minutes, but this does not mean that the paint is fully dry or cured. Some paints will require 2 to 4 hours before they are fully dry.

Because each brand of paint is different refer to the label for exact drying times.

Consider priming your lampshade. If your lampshade is a very dark color and you want to paint it a lighter color, you might want to prime it first. This is because many lighter colored paints are translucent and the darker color may show through.

You can prime your lampshade by painting it with a white paint primer. You can use a paintbrush or a foam roller to apply the paint. You can also use a white primer spray paint. Be sure to let the primer dry before you move on to the next step.

Iron the fabric, if necessary. If there are any wrinkles in the fabric, you will need to iron them out. If you don’t do this, the wrinkles will show up in your finished piece.[14]

Tuck the bottom and top edges into the lampshade. Place a line of glue inside the lampshade, just beneath the wire rim. Carefully fold the top and bottom seam over the edge of the lampshade, and onto the inside.

Run your finger along the fabric to seal it. You may notice that your lampshade has metal bars either on the top or bottom. You fabric will lay across those bars instead of laying smoothly across the lampshade.

To prevent this from happening, take your scissors and cut a slit into the seam. Press the fabric down to either side of the metal bar.[11]

Español: pintar vidrio, Deutsch: Glas bemalen, Português: Pintar Vidro, Italiano: Dipingere il Vetro, Русский: расписать красками стекло, Français: peindre du verre, Bahasa Indonesia: Melukis Kaca, Nederlands: Glas verven met glasverf, العربية: الرسم على الزجاج

Let the paint dry and cure in a dust-free place. How long this takes depends on the type of paint you used. Glass paint can take up to 24 hours to dry, while decoupage glue will only need a few hours. Some paints also have a curing time, so double-check the label.

If the paint feels sticky, that means it has not finished curing. Leave it alone for a few more days.

Replace the panels on the paper. Set the glass panels on top of the paper, making sure to match them up with the original tracings. If you will be using glue to make the leading and paint, coat the glass panels with clear, acrylic sealer.

This will give the glue something to stick to. You can do this right over the paper.[10] You’ll be working on this project over the course of 2 to 3 days, so set up your workstation some place that won’t get in the way.

Outlay a design in lead. To do this, use either the strip or squeeze-on variety, depending on what you want. Use your stencil or transfer if available, or use freehand. An alternative to this method is to use permanent marker as your outlay.

When painted over and fired, the permanent marker will usually not show, and lead and paint won’t mix.

Cover a small patch of the lampshade with Mod Podge. The patch should be a little bit bigger than the size of your square. Use a paintbrush or a foam brush to apply the Mod Podge. You will be working in small patches so that the Mod Podge does not dry out.

If you do not have any Mod Podge, you can make your own by mixing 1 part white school glue with 1 part water.

Consider drawing some designs onto your lampshade using a hot glue gun. This will create a raised effect on the surface of your lamp after you paint it. You can make little dots, squiggles, or swirls. You can draw spirals, vines, leaves, or even birds.

[4]

Choose a paneled glass lamp shade. Not only will this make your stained glass lamp look more authentic, but it will be easier to paint as well. Purchase a lamp shade with 4 or more panels set into a metal frame.

Vintage lamp shades work especially well here.[7]

Use a pipette to apply the paint to each section of your design. There are two ways to do this. You can add the paint by the drop, as you move your hand across the desired surface area; or if the volume of the paint is enough, and you find you now you have gaps between spots, even it up uniformly by drawing a toothpick through the area in lines, back and forth.

This will also help in ridding the piece of any air bubbles trapped in the paint.

Cover the side seams with ½ inch (1.27 centimeter) wide ribbon. Take a piece of ribbon and cut it so that it is 1 inch taller than your lampshade. Run a line of hot glue or fabric glue down one of the vertical seam on your lampshade (right where two panels join.

Press the ribbon down onto the glue so that it covers the entire seam. There should be ½ inch (1.27 centimeters) of extra ribbon sticking over the top and bottom of your lampshade. Repeat this step for the rest of the seams.

Use caution when working with hot glue guns. The high-temp ones can cause blisters if you accidentally touch the nozzle of glue. If you are worried about this, consider using a low-temp one. It won’t be as strong, but you’ll be less likely to get blisters from it.

Carefully trace the panel onto the tracing paper. Trace over the top and bottom of the panel. Also, trace over the left and right side seam.

Pour some paint out onto a paper plate or palette. The best types of paint to use are fabric paints or acrylic paints.

Decide how you want the lampshade to look like in the end. Do you want to decorate the entire lampshade? Or do you just want to add a trim to the top and bottom? Get out a piece of paper and sketch out a few designs.

If you are having trouble coming up with a design, look at pictures of lampshades online or in a catalogue. Consider basing your lampshade off of a certain theme, such as Asian, Mexican, tribal, nature, or holiday.

Depending on the media, you should really just be able to lay down the colors separately and mix them with gentle brushstrokes across 2 at a time.

Lay a large piece of paper on a flat surface. The paper should be taller than the lampshade, and wide enough for the lampshade to roll across it. You will be using this to make your template.

Place your stencil against the lampshade and tape it in place, if necessary. Some stencils have an adhesive back, so they should stick to your lampshade on their own. Other stencils are not adhesive and will move around.

To keep that from happening, place your stencil where you want it, then secure it with a piece of painters tap or masking tape on each side of the stencil.

Press the fabric panels onto the lampshade. Each panel will overlap by ½ inch (1.27 centimeters) at the seam. Make sure that there is ½ inch (1.27 centimeters) of extra fabric at the top and bottom of your lampshade.

You will be folding this excess fabric inside your lampshade.

Like all paint varieties, glass paint comes in two types, water and oil based. Painting on glass is particularly enjoyable because glass makes a great canvas as it’s surface is smooth, it reflects light brilliantly, and offers the artist various choices. If you want to learn the basics of painting on glass, read on for a fascinating discussion.

Reassemble the lamp. Once the paint has completely dried and cured, you can reassemble the lamp. If the paint still feels tacky, it has not finished curing. Give it a few more hours; double-check the label for more complete drying times.

Let your traced design dry for at least 6 to 8 hours. This is vital, regardless of the type of media you used: glass paint leading, puffy paint, or glue. If the outlines are still wet, then the next part won’t work.

[14] Some paint needs longer to dry. Check the label on your bottle of paint if you are not sure.

Consider covering your lampshade with objects you have laying around the house. You don’t have to do all of the steps in this method. Choose the one you like best.

Consider painting your lampshade a solid color first. You don’t have to do this, but it can give your lampshade a while new look. For example, you can paint your lampshade turquoise and stencil some white designs onto it.

You could also paint your lampshade white, and stencil some gold designs onto it.

Consider priming the lampshade. If your lampshade is a very dark color and you are planning on using a lighter color of fabric, you might want to paint the lampshade white first. You can apply white acrylic primmer with a paintbrush or a foam brush.

You can also spray the entire lampshade using a white primer spray paint.[8]

Thanks to all authors for creating a page that has been read 31,280 times.

Apply a second coat of paint, if desired, and let it dry. This will give you a more opaque finish and help conceal any brushstrokes. Alternatively, you can paint the inside of the lamp shade–just be sure to wipe the inside down with rubbing alcohol first.

[4] How long this takes depends on the type of paint you used, so check the bottle to be sure. Let this second coat or inside coat dry and cure completely.

Apply the paint to the outside of the lamp shade. Hold the lamp shade from the inside, and apply the paint with a wide, flat brush. Make all of your brushstrokes point in the same direction: up-and-down or side-to-side.

Apply a light, even coat to reduce brushstrokes.[3] Use a brush made from synthetic taklon bristles for best results. Avoid camelhair (too soft) or boar bristle (too stiff).

Seal the lampshade to protect your work. You can do this by brushing more Mod Podge over the lampshade using a foam brush or a paintbrush. You can also spray the entire lampshade using a clear, acrylic sealer.

This will help protect your work, and prevent it from peeling. If necessary, wait for the first coat to dry before applying a second one.

Pour some paint onto a paper plate or paint palette. The best type of paint to use is fabric paint or acrylic paint. If the paint is very thick, you might end up with some visible brushstrokes. You can remedy this by mixing a few drops of water into the paint.

Roll the lampshade across the paper while tracing the top and bottom edge. Stop when you reach the seam again.[9]

Take a piece of tracing paper and pin it to one of the panels. Use straight pins, and stick them straight down into the lampshade. You can also tape the tracing paper to the lampshade.

Create your own artwork using a permanent marker or a fabric pen. You can draw simple designs like spirals or flowers. You can even write down the words to your favorite poem, song, or book passage.

Outline your design with glass paint leading. Purchase a bottle of black glass paint leading from the craft store. Apply the leading straight onto the glass from the bottle’s nozzle. Start from the left side if you are right-handed, and vice versa if you are left-handed; this way, you won’t smear your work.

Make sure that the lines connect, or the paint will bleed when you apply it.[11] If you don’t want to use glass paint, use black puffy paint or black dimensional paint instead.[12] Make your own puffy paint by mix 1 teaspoon of black acrylic paint into an 8-ounce (240-mL) bottle of white school glue.

[13]

Include your email address to get a message when this question is answered.

Choose your stencil. Do you want a pattern that covers the lamp completely? Or do you want to stencil on a small design (such as a flower or bird) here and there?

Allow the lampshade to dry. This can take anywhere from a few hours to a day, depending on how dry or humid it is.

Did you try these steps?Upload a picture for other readers to see.

Yes, but you’ll need to seal it with something or the paint will come off easily.

Reassemble the lamp. Once the paint has dried completely and is no longer tacky, put the panels back into the frame; make sure that the painted side is facing out. If the paint still feels tacky, it is not completely dry; wait a few more days for it to finish drying and curing.

If you used glue and paint for your lamp, seal the panels with clear, acrylic spray paint first.[20]

Let the paint dry for at least 24 hours. The glue-and-acrylic paint mixture may dry faster, but you will need to wait at least 24 hours if you used real glass paint. Keep in mind that some brands also include a curing time, so double-check the label for complete drying and curing instructions.

[18] If you notice any gaps in your paint, wait until the paint dries, then fill them in with a permanent marker in a matching color.[19]

Take the lampshade off and connect the top and bottom lines. Use a ruler to make the lines even. If your lampshade is wider at one of the ends, you will end up with something that looks like an arch. If your lampshade is the same width at the top and bottom, you will end up with something that looks like a rectangle.

[10]

Remove the lamp shade and clean it. Take the lamp shade off of the fixture. Wash it with warm, soapy water, then dry it off with a towel. Wipe the lamp shade down with rubbing alcohol to remove any oil or residue.

Handle the lamp shade from the inside from now on to prevent oil transfer. Do not clean the lamp shade if you already painted it.

Make your own paint with glue and dye if you cannot find glass paint. Choose a decoupage glue (e.g. Mod Podge) in a finish that you like: glossy, satin, or matte. Pour enough glue to coat your lamp shade into a disposable container, then stir in 1 to 5 drops of food coloring.

Keep stirring until the color is consistent and no streaks remain.[2] The more food coloring you add, the deeper the color will be. A glossy finish will look more translucent, while a matte finish will give you a sea glass effect; satin will give you something in between.

Related Images of 3 Ways To Paint Glass Lamp Shades Wikihow
3 ways to measure a lamp shade wikihow how to measure a lamp shade image titled how to size a lampshade
Method 1 selecting light fixtures image titled brighten your room step 1
Method 1 enhancing lighting image titled decorate a kitchen step 15
Image titled brighten up your home decor step 1
Image titled make a mini greenhouse step 4
Image titled paint ceramic step 1
The
Image titled paint a wall step 1
Image titled paint a wall step 9
Image titled choose paint colors for your basement step 1
Image titled make mason jar lights step 1
Image titled decorate a kitchen step 1
How to paint a ceramic lamp base best of susan snyder painting glazed ceramic vase of
Image titled dye glass step 1
Image titled paint pvc step 1
Extraordinary
Image titled paint clouds step 1
Image titled paint plastic models step 1
Hallway Lighting Design And Inspiration Crompton Lighting Pty
Hallway Lighting Design And Inspiration Crompton Lighting Pty

Hallway Lighting Design And Inspiration Crompton Lighting PtyHallway Lighting Design And Inspiration Crompton Lighting Pty The living room is where […]

Fiona Crystal Table Lamp Williams Sonoma
Fiona Crystal Table Lamp Williams Sonoma

Fiona Crystal Table Lamp Williams SonomaFiona Crystal Table Lamp Williams Sonoma Thick planes of solid optic crystal intersect to form […]

Lighting Fixtures Grande Prairie
Lighting Fixtures Grande Prairie

Lighting Fixtures Grande PrairieLighting Fixtures Grande Prairie Lux kitchen bath lighting grande prairie ab ca Flush mount light fixtures Lux […]

Bronze Flower Torch Lamp World Market
Bronze Flower Torch Lamp World Market

Bronze Flower Torch Lamp World MarketBronze Flower Torch Lamp World Market System error: Failed to submit email, please contact website […]

Chandelier Shades On Bellacor
Chandelier Shades On Bellacor

Chandelier Shades On BellacorChandelier Shades On Bellacor Off White Silk Bell Clip Chandelier Shade w/ Corn Silk Fringe & Beads […]

Flush Mount Ceiling Lights Lighting Direct
Flush Mount Ceiling Lights Lighting Direct

Flush Mount Ceiling Lights Lighting DirectFlush Mount Ceiling Lights Lighting Direct Laguna 3 Light 16″ Wide Semi-Flush Ceiling Fixture with […]