How To Install Low Voltage Landscape Lighting This Old House

tech lighting How To Install Low Voltage Landscape Lighting This Old House

tech lighting How To Install Low Voltage Landscape Lighting This Old House

All about landscape lighting yard lightingdiy exterior lightingoutdoor
How to put in landscape lighting this old house
How to install low voltage landscape lighting this old house
Quality low voltage led landscape lighting
Landscape path lights basics of line vs low voltage systems
Landscape lighting
Outdoor lighting landscape lighting exterior lighting low voltage lighting
22 landscape lighting ideas diy network landscaping and dark spots
Up lighs along house area path lights along planters low voltage lighting
Low voltage night lighting of a brick home in north reading ma
Outdoor landscape lighting a great way for house illumination
Learn what factors affect the cost of landscape lighting in idaho
Low voltage lighting st louis landscaping consultants
Low voltage night lighting of an old colonial home in newburyport ma
Landscape lighting ideas outdoor landscape lighting pics
Manor house low voltage lighting landscape manor house low voltage lighting
22 landscape lighting ideas home improvement diy network
Low voltage night lighting of a colonial home in byfield ma
Light where you need it this old house
Manor house low voltage lighting house landscape lighting evening shadows offers full design and installation of

Set the pathway light fixtures on the ground where they’ll be installed — usually about 8 to 10 feet apart.

Tip: In regular use, promptly replace a burned-out bulb or it will shorten the life of the other bulbs.  

Tip: If necessary, set the light fixtures on top of the folded sod to prevent it from flopping back down.  

Smooth the soil over the trench, but leave the cable sticking up out of the soil near each fixture.

Tip: Don’t bury the cable more than 3 inches or you’ll have difficulty connecting the light fixture.  

Get the latest This Old House news, updates and special offers every week, direct to your inbox.

Continue installing the remaining fixtures in the same manner.  

Tip: If none of the bulbs lights up, you may have a faulty transformer or outdoor electrical outlet.  

Position the first fixture as close to the edge of the walkway as possible without any part of it hanging over. (If the fixture extends into the walkway, people will constantly be bumping into it.)

Xcsource 10pcs 50mm PH2 1/4″ Hex Shank Magnetic Phillips Head Screwdriver Bits Titanium Coated S2 Steel Power Tools BI214

IRWIN VISE-GRIP Multi-Tool Wire Stripper/Crimper/Cutter, 2078309

If necessary, cut the sod around the light fixtures with the shovel.

Make a hole in the ground for the fixture’s stake with a large screwdriver or long steel punch. Never use a hammer to drive the fixture into the ground.

Slip the two connector halves hanging from the bottom of the light fixture over the cable that’s protruding from the sod and pinch them together until you hear a click. This allows the sharp prongs inside the connectors to pierce the cable and make contact with the wires inside.

Once all the light fixtures are installed and working properly, smooth out the sod around the fixtures.

Make a slit in the detached sod where the fixture will sit and fold the sod back over the soil, keeping the cable for each fixture above the grass.

Run the cable up to the outdoor electrical outlet. Then use wire strippers to cut the cable and strip off ½ inch of the rubber insulation.

When you come to an obstacle, such as a fence or shrub, string the cable under or around it.

Get the latest news, updates and offers from This Old House to your inbox

Drive a wood stake into the ground next to the outlet. Then screw the transformer to the stake. (It can also be mounted directly to the wall of the house.)

Take a flat-blade shovel and slide it underneath the top layer of grass, about 12 inches in from the edge of the walk. Then lift up on the handle to separate the grass from the soil, and fold over this scalped portion of sod. Continue in this manner all along the walkway.

Tip: Put first fixture at least 10 feet from the transformer.  

The AMES Companies, Inc Jackson Pony Moulder/Asphalt Square Point Shovel – 1227600

Set the low-voltage electrical cable in the trench. Leave a bit of slacked cable at each fixture point for making the connection to the light fixtures.

Slide the stripped wires under the two terminal screws on the bottom of the transformer. Tighten the screws all the way to hold the cable securely in place.

The transformer steps down the 120-volt house current to just 12 volts. It must be plugged into a GFCI-protected outdoor electrical outlet fitted with a “while-in-use” cover, and oversize plastic box that closes over the power cord. The transformer needs to have enough capacity to support the cumulative wattage of the lights in the system. Between fixtures, the cable is buried in a shallow trench. As long as you have a nearby outlet, you’ll be able to give your home and yard a welcoming glow when the sun goes down.

Tuck the cable and connector under the sod and stuff them into the soil, about 2 inches deep.

Since the transformer is plugged in, the fixture should light up, confirming the connection is good. If it doesn’t, unsnap and resnap the connector, or check the bulb.

Use the corner of the shovel’s blade to scratch a 3-inch-deep trench in the soil where the wire will go.

Tip: Don’t place a light within 10 feet of a pool, spa, or fountain.  

Lay the low-voltage cable along the concrete walkway, following the line of light fixtures. Use 14-gauge cable for lighting systems that total 200 watts or less and 12-gauge cable for systems that are more than 200 watts.

Find TV listings for This Old House and Ask This Old House in your area.

Low-voltage landscape lighting is a simple improvement that can make a huge difference in how your home looks after dusk and in its safety and security as well. Installed along walkways, steps, and driveways, or pointing up at trees, walls, and fences, the typical low-voltage lighting system requires just three components: a transformer, low-voltage electrical cable, and the fixtures. You don’t have to be comfortable with wiring—or even have ever done any—to install this type of system.

Set all the light fixtures back into position, checking to make sure they’re equally spaced.

Lift up the “while-in-use” cover on the outlet and plug in the transformer.  

Firmly press down on the sod, then use a garden hose to soak the area with water.

Using both hands, push the fixture and its stake into the ground until the top of the stake is flush with the ground. Eyeball the fixture to make sure it’s not tilted to one side.

How To Install Low Voltage Landscape Lighting This Old House